INK RIBBON AVALIABLE VIA E BAY http://www.ticketmachinewebsite.com/apps/photos/ INK RIBBON AVALIABLE VIA E BAY AVALIABLE VIA E BAY The Setright is a fantastic piece of ticket machinery.That should print a nice ticket every time.The ink ribbon illustrated is 1 meter in length and will print 15,000 nice tickets.If you need any help just post a note on the ticket machine talk or forum page and your sure to be helped .The ticket jamm and fitting a new ticket roll are also covered in this section http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219293 27219293 PLEASE READ THIS BEFORE YOU START Fitting a new ink ribbon can be very rewarding but can be very messy.Rubber gloves should be worn and plenty of newspaper should be used to stop ink staining.Be very carefull with sharp tools and always work awy from your body. http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219280 27219280 OPENING YOUR MACHINE First the end plate needs to be removed,to do this the fixing screw needs to be extracted .<BR>When the machine is in this position it will be discribed as "FS" and when turned over with the handle on the left side this will be discribed as "RS" . http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219294 27219294 MACHINE SEALS SOME MACHINES MAY STILL HAVE THERE SEALS INTACT AND THESE NEED TO BE REMOVED,IF YOU HAVE A CUP SEAL YOU WILL NEED TO DIG OUT THE RUBBER/WAX TO ACCESS THE SCREW,IF YOU HAVE A LEAD SEAL YOU WILL NEED TO BREAK OF WITH PLIERS ETC TO ACCESS THE SCREW,IF A SHEAR SCREW IS FITTED THIS WILL NEED TO BE DRILLED TO TURN(SEE GIBSON RE INKING INSTRUCTIONS)THE SCREW ON THE RIGHT WILL NEED A SMALL SCREWDRIVER PLACED IN ONE OF THE GROVES AND TAPPED AROUND ANTI CLOCK WISE http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219281 27219281 REMOVE SIDE CASING "FS" & "RS" ONCE THE END PLATE HAS BEEN REMOVED SLIDE THE CASING OFF IN THE DIRECTION SHOWN ,TURN OVER THE MACHINE AND REPEAT THE PROCESS WITH THE REAR CASING,THESE MAY BE STIFF ,IF SO APPLY WD40 ETC http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219282 27219282 CUTTING THE INK RIBBON "FS" THE OLD BOBBIN/RIBBON HAS TO BE REMOVED AND THE NEW RIBBON PUT IN ITS PLACE,CUT THE RIBBON AS IN PICTURE,DO NOT PULL THE REMAINING OLD RIBBON THROUGH THE MACHINE AS YOU WILL NEED TO ATTACH THE NEW RIBBON TO THE OLD RIBBON TO PULL IT THROUGH THE MACHINE http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219295 27219295 REMOVAL OF INK RIBBON "FS" THE INK BOBBIN NEEDS TO BE HANDLED WITH CARE AS IT WILL FIRE OUT THE SPRING IF YOU ARE NOT CAREFULL,HANDLE AS SHOWN IN PICTURE,MOVE SLOWLY TO THE EDGE OF MACHINE AND COVER BOTH ENDS TO KEEP THE SPRING COMPRESSED WHEN REMOVING ,once removed pull out pivot and spring(shown at end of index finger) and re fit to replacement bobbin http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219283 27219283 PULLING NEW RIBBON THROUGH MACHINE "FS" ATTACH NEW RIBBON TO THE OLD RIBBON AS IN PICTURE ,USE NEEDLE ,OR STAPLE,THEN VERY CAREFULLY PULL NEW RIBBON THROUGH MACHINE ,ONCE THROUGH TAKE OUT NEDDLE ETC,TAKE YOUR TIME DOING THIS ,ONCE THROUGH ATTACH NEW RIBBON TO BACK BOBBIN http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219284 27219284 BOBBIN COPPER/FELT SPACERS "FS" YOUR MACHINE MAY HAVE ONE OF THE ABOVE FITTED BELOW THE FRONT BOBBIN,WHEN NEW BOBBIN FITTED ,PLACE AT THE BOTTOM OF THE BOBBIN,THIS WILL HELP KEEP THE RIBBON IN THE CORRECT POSITION http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219296 27219296 REMOVAL/FITTING OF RIBBON FROM BACK BOBBIN "RS" UNWIND AND REMOVE OLD BACK RIBBON FROM BOBBIN ONCE PULLED THROUGH MACHINE,YOU WILL NEED TO REMOVE THE SMALL CLIP ,FIT THE NEW RIBBON TO THE BOBBIN AND RE SECURE WITH CLIP,MAKE SURE THE GEARED END OF THE BOBBIN IS AT THE BOTTOM,ONCE THIS IS DONE THE BOBBIN/RIBBON IS READY TO BE RE FITTED http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219305 27219305 FIT /REMOVE RIBBON FROM BOBBIN "RS" http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219297 27219297 REMOVAL/FITTING OF BACK BOBBIN "RS" THE BACK BOBBIN IS FITTED IN THE SAME WAY AS THE FRONT BOBBIN ,BUT HAS A SMALL GEAR WHEEL FITTED,THIS TURNS THE RIBBON VERY SLOWLY AS THE TICKET IS ISSUED THE SPRING LOADED PIVOT AT THE BOTTOM OF THE BOBBIN NEEDS TO BE COMPRESSED AT BOTH ENDS,(NEARLY FLUSH WITH THE MACHINE BODY PLATES) TO RE FIT http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219298 27219298 RE FITTING BACK BOBBIN/ RIBBON "RS" ONCE YOU HAVE WOUNED THE NEW RIBBON ON TO THE BOBBIN ,SLOT THE BOBBIN BACK AND BE SURE THAT THE BOBBIN SPRING LOADED PIVOTS FIT CORRECTLY IN THE INDENTS AND THE GEAR WHEEL ON THE BOBBIN FITS IN TO THE SMALL GEAR IN THE MACHINE ,WHEN THIS IS FITTED TIGHTERN THE SLACK BY WINDING THE GEAR WHEEL ILLUSTRATED AT THE END OF THE SCREWDRIVER,MAKE SURE THE RIBBON IS NICE AND TIGHT http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219299 27219299 FITTING A BOBBIN TO EMPTY MACHINE "FS" IF YOUR MACHINE DOES NOT HAVE A RIBBON/BOBBIN TO ATTACH THE NEW RIBBON TO ,THEN YOU CAN PUSH THE RIBBON THROUGH THE MACHINE ,BE CAREFULL NOT TO TOUCH THE PRINT WHELLS IN THIS PROCESS,AS THIS CAN DAMAGE THE PRINT FACE http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219306 27219306 FITTING A BOBBIN TO EMPTY MACHINE 2 "RS" TURN THE MACHINE OVER AND PULL THE RIBBON THROUGH AND ATTACH TO BACK BOBBIN http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219307 27219307 KEEP BOBBIN LEVEL "FS" &"RS" KEEP THE BOBBIN AS LEVEL AS YOU CAN WHEN FITTING/REMOVING http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219308 27219308 TICKET JAMM 1 "FS" THE MOST COMMON TICKET JAMM ON A SETRIGHT IS IN BETWEEN THE TICKET FEED AND TICKET CHANNEL ,AS SHOWN IN THE PICTURE, TOP LEFT ABOVE THE TWO GEARWHEELS,TWEZZERS, A LONG INSTRUMENT (KNIFE ETC) AND PATIENCE WILL BE REQUIRED, BE CAREFULL WITH SHARP TOOLS http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219309 27219309 TICKET JAMM 2 BEFORE YOU TRY TO CLEAR THE TICKET CHANNEL YOU MUST OPEN THE TICKET TENSION LEVER,SIMPLY TWIST WITH YOUR THUMB AND INDEX FINGER http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219310 27219310 TICKET JAMM 3 THE TICKET TENSION LEVER IS OPENED IN THIS POSITION,WHEN OPENED YOU CAN INSERT INSTRUMENTS/NEW TICKET ROLL,TO ISSUE TICKETS TWIST BACK TO LOCK POSITION http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219311 27219311 TICKET JAMM 4 TO CLEAR THE CHANNEL PUSH INSTRUMENT INTO TICKET FEED AS SHOWN AND FORCE THE JAMMED TICKET TO MOVE,THEN PICK IT OUT WITH THE TWEEZERS,THE AREA TO CONCENTRATE ON IS WHERE THE TWEEZERS ARE ALIGNED IN PICTURE http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219312 27219312 TICKET JAMM 5 IF UNABLE TO TOTALY CLEAR ,UNSCREW BRASS PLATE AND REMOVE (TOP CENTRE ABOVE TWEZZERS IN PICTURE) AND PULL OUT ANY PIECES OF TICKET IN CHANNEL ETC,A SMALL MAGNETIC SCREWDRIVER IS ALWAYS RECOMMENDED WHEN WORKING ON SETRIGHTS(IN CASE SCREWS FALL INTO MACHINE ETC) http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219313 27219313 TENSION LEVER LOCK DO NOT INSERT INSTRUMENTS /NEW TICKET ROLL WHILE THE LEVER IS IN THIS POSITION http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219300 27219300 FITTING NEW TICKET ROLL 1 MAKE SURE THE TICKET TENSION LEVER IS OPEN ,THREAD THE NEW TICKET ROLL THROUGH THE MACHINE http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219314 27219314 FITTING NEW TICKET ROLL 2 A GOOD TIP IS TO FOLD OVER THE END OF THE TICKET ROLL BEFORE INSERTING IT THROUGH THE MACHINE WHICH MUST BE AS STRAIGHT AS POSSIBLE http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219315 27219315 FITTING NEW TICKET ROLL BEFORE INSERTING NEW TICKET ROLL ,STRAIGHTEN THE END OF THE ROLL BY RUNNING IT THROUGHT YOUR THUMB AND INDEX FINGER UNTIL IT IS NICE AND STRAIGHT http://www.ticketmachinewebsite.com/apps/photos/photo?photoID=27219316 27219316